Campbell-scientific 109SS Temperature Probe Manuel d'utilisateur

INSTRUCTION MANUAL Model 109SS Temperature Probe Revision: 3/14 Copyright © 1983- 2014 Campbell Scientific, Inc.

Model 109SS Temperature Probe 8. If LoggerNet, PC400, RTDAQ, or PC200W is running on your PC, and the PC to datalogger connection is active, you can

Model 109SS Temperature Probe Maximum Steinhart-Hart Linearization Error: 0.02 °C at –40 °C FIGURE 6-1. Worst-case probe and measurement er

Model 109SS Temperature Probe Stainless-Steel Sheath Diameter: 0.16 cm (0.063 in) Length: 5.84 cm (2.3 in) Overmolded Joint Diameter: 1.02

Model 109SS Temperature Probe Short Cut cannot edit programs after they are imported and edited in CRBasic Editor. A Short Cut tutorial is available i

Model 109SS Temperature Probe 1: AC Half Bridge (P5) 1: 1 Reps 2: 25 2500 mV 60 Hz Rejection Range 3: 1 SE Channel 4: 1

Model 109SS Temperature Probe 7.3 Water Temperature Installation 109SS probes can be submerged to 45 m (150 ft) or 63 psi. The 109SS is not weighted

Model 109SS Temperature Probe The ratio of measured voltage (Vs) to excitation voltage (Vx) is related to thermistor resistance (Rs) and the 24.9 kΩ f

Model 109SS Temperature Probe where: Tk = temperature in Kelvin X = 0.001 • ln(Rs) C0 = A = 0.001129 C1 = B • 1E3 = 0.234108 C2 = 0 C3 = C • 1E9 = 87.

Model 109SS Temperature Probe Therm109(T109_C,1,1,1,20000,_60Hz,1.0,0.0) Integration options and the settling time parameter are not available for CR2

Model 109SS Temperature Probe 9.2 Maintenance The 109SS probe requires minimal maintenance. Periodically check cabling for signs of damage and possi

Model 109SS Temperature Probe 14

Appendix A. Importing Short Cut Code This tutorial shows: • How to import a Short Cut program into a program editor for additional refinement. • H

Appendix A. Importing Short Cut Code 6. Import wiring information to the program by opening the associated .DEF file. Copy and paste the section be

Appendix B. Example Programs B.1 Example CRBasic Programs B.1.1 Example 1 — Sample program for CR200(X) series dataloggers 'Program measures

Appendix B. Example Programs '*AG = Analog Ground (represented by ground symbol on CR1000 wiring panel 'Declare the variables for the temp

Appendix B. Example Programs 'Call the data table CallTable AvgTemp NextScan EndProg B.2 Example Edlog Program This example can be u

Appendix B. Example Programs 7: Polynomial (P55) 1: 1 Reps 2: 6 X Loc [ Scal_lnRt ] 3: 7 F(X) Loc [ 1_Tk ] 4: .001129

Appendix C. Conversion of Thermistor Resistance or Voltage Ratio to Temperature TABLE C-1. Voltage Ratio, Resistance, and Temperature1 Actual Tempe

Appendix C. Conversion of Thermistor Resistance or Voltage Ratio to Temperature 3 28054.4 3.02 3.00 4 26687.5 4.02 4.00 5 25395 5.02 5.00 6 24172.5 6

Appendix C. Conversion of Thermistor Resistance or Voltage Ratio to Temperature 59 2578.6 59.03 59.00 60 2487.1 60.03 60.00 61 2399.4 61.03 61.00 62

Limited Warranty “Products manufactured by CSI are warranted by CSI to be free from defects in materials and workmanship under normal use and service

Appendix C. Conversion of Thermistor Resistance or Voltage Ratio to Temperature C-4

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbe

Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing

Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to spec

Table of Contents B. Example Programs ... B-1 B.1 Example CRBasic Programs ...

Model 109SS Temperature Probe 1. Introduction The 109SS Temperature Probe uses a thermistor to measure temperature in soil and water. It is compati

Model 109SS Temperature Probe 3. When Short Cut opens, select New Program. 4. Select Datalogger Model and Scan Interval (default of 5 or 10 second

Model 109SS Temperature Probe 5. Under the Available Sensors and Devices list, select the Sensors | Temperature folder. Select 109 Temperature Probe