Campbell-scientific CR10X Measurement and Control System Manuel d'utilisateur Page 242
- Page / 362
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
APPENDIX B. CONTROL PORT SERIAL I/O INSTRUCTION 15
B-10
TABLE B-2. CR10X/Barometer Connection Details
CAUTION: To avoid damage to the
barometer CMOS chips, connect ground
first and power last. All sensor leads not
used in a particular hook-up configuration
should be insulated to avoid possible
shorting.
B.6.1.3 INSTRUCTION 15 PARAMETER
CONSIDERATIONS
The AIR Barometer requires only the CR10X's
RTS/DTR connected to its shut down or DTR line
to transfer data. No CTS or output is required. It
therefore uses 2 CR10X ports, as described by
"CONFIGURATION 1" (Section B4).
If one AIR barometer is connected according to
Hook-up #1 with only one sample output, the
parameters are as follows:
01: 1 Repetitions
02: 00 Configuration code of
ASCII/TTL/1200 baud
03: 0 CTS/Delay before send (does
not matter)
04: AB Control ports, (User’s choice)
A to sensor Shut Down.
B to RXD.
05: 0 Output start location (no output
from CR10X)
06: 0 Number of locations to send
(no output from CR10X)
- OPERATOR'S MANUAL 1
- WARRANTY AND ASSISTANCE 3
- TABLE OF CONTENTS 5
- DATA RETRIEVAL/COMMUNICATION 6
- PROGRAM EXAMPLES 7
- INSTRUCTIONS 7
- INSTALLATION 8
- APPENDICES 8
- CR10X TABLE OF CONTENTS 10
- This is a blank page 10
- SELECTED OPERATING DETAILS 11
- CAUTIONARY NOTES 12
- OV1. PHYSICAL DESCRIPTION 13
- CR10X WIRING PANEL 14
- CR10X OVERVIEW 15
- OV2. MEMORY AND PROGRAMMING 17
- CONCEPTS 17
- OV5. PROGRAMMING EXAMPLES 25
- 32 converts the 29
- Phone Modem 33
- Copyright © 1986, 2001 35
- Campbell Scientific, Inc 35
- Printed September 2001 35
- ARRAYS, AND MEMORY POINTERS 51
- 3.5 VOLTAGE RANGE AND 56
- OVERRANGE DETECTION 56
- 3.6 OUTPUT PROCESSING 56
- PROGRAM CONTROL 57
- 3.9 INSTRUCTION MEMORY AND 59
- EXECUTION TIME 59
- 3.10 ERROR CODES 63
- 4.1 ON-LINE DATA TRANSFER 65
- INSTRUCTION 96 65
- 4.4 STORAGE MODULE 68
- 5.1 TELECOMMUNICATIONS 71
- COMMANDS 71
- 6.1 PIN DESCRIPTION 77
- 6.2 ENABLING AND ADDRESSING 78
- PERIPHERALS 78
- 6.3 RING INTERRUPTS 79
- 6.6 SYNCHRONOUS DEVICE 80
- 6.7 MODEM/TERMINAL AND 81
- COMPUTER REQUIREMENTS 81
- 7.1 SINGLE-ENDED VOLTAGE/ 85
- 7.2 DIFFERENTIAL VOLTAGE 87
- MEASUREMENT 87
- 7.5 107 TEMPERATURE PROBE 89
- 7.6 207 TEMPERATURE AND RH 89
- 7.7 ANEMOMETER WITH 90
- PHOTOCHOPPER OUTPUT 90
- 7.12 PRESSURE TRANSDUCER - 4 95
- WIRE FULL BRIDGE 95
- 7.15 NONLINEAR THERMISTOR IN 99
- HALF BRIDGE (MODEL 101 PROBE) 99
- PRESSURE TRANSDUCER 104
- 7.18 4 TO 20 MA SENSOR USING 107
- CURS100 TERMINAL INPUT 107
- 8.1 COMPUTATION OF RUNNING 109
- 8.2 RAINFALL INTENSITY 110
- 8.3 USING CONTROL PORTS AND 111
- LOOP TO RUN AM416 111
- MULTIPLEXER 111
- SYNCHED TO REAL TIME 113
- PORTS (RAIN GAGE) 113
- 8.6 SDM-A04 ANALOG OUTPUT 114
- MULTIPLEXER TO STRIP CHART 114
- 8.7 CONVERTING 0-360 WIND 115
- DIRECTION OUTPUT TO 0-540 FOR 115
- STRIP CHART 115
- - SAVING DATA PRIOR TO EVENT 116
- 03: Do (P86) 118
- 8.10 COVARIANCE CORRELATION 119
- PROGRAMMING EXAMPLE 119
- 8.11 FAST FOURIER TRANSFORM 123
- EXAMPLES 123
- POWER SENSORS 130
- zero yields 138
- Silicon diodes 148
- Parameters 6 151
- Cos ( ') ( ') / 177
- SEQUENCE 193
- 13.2 SINGLE-ENDED AND 194
- DIFFERENTIAL VOLTAGE 194
- MEASUREMENTS 194
- LENGTH ON THE SIGNAL SETTLING 195
- 13.4 THERMOCOUPLE 204
- 13.6 RESISTANCE MEASUREMENTS 213
- REQUIRING AC EXCITATION 213
- 14.1 PROTECTION FROM THE 217
- ENVIRONMENT 217
- 14.2 POWER REQUIREMENTS 217
- SUPPLIES 218
- 12V ALKALINE BATTERY PACK 219
- Y U A S A 220
- 14.4 SOLAR PANELS 221
- TO THE CR10X WIRING PANEL 222
- 14.6 VEHICLE POWER SUPPLY 222
- CONNECTIONS 222
- 14.7 GROUNDING 223
- 14.8 WIRING PANEL 224
- 14.9 SWITCHED 12 VOLT 224
- SWITCHING RELAYS 224
- 14.11 MAINTENANCE 226
- DESI PAK 227
- APPENDIX A. GLOSSARY 229
- B.1 SPECIFICATIONS 233
- B.3 INSTRUCTION 15 AND 234
- PARAMETER DESCRIPTIONS 234
- AND SENSOR WIRING 237
- B.5 INPUT DATA FILTERS 238
- B.6 PROGRAM EXAMPLES 240
- COMMUNICATION 246
- C.1 TELECOMMUNICATIONS 249
- COMMAND WITH BINARY 249
- RESPONSES 249
- C.2 FINAL STORAGE FORMAT 252
- C.3 GENERATION OF SIGNATURE 253
- APPENDIX E. ASCII TABLE 259
- F1. FUNCTION 261
- F2. INSTRUCTION DETAILS 261
- G.1 INTRODUCTION 265
- G.2 EXAMPLE PROGRAM—PHONE 265
- CALLBACK BASED ON A CONDITION 265
- G.3 PC208W WINDOWS SOFTWARE 266
- AND COMPUTER SETUP 266
- AND ITS COMPUTER SETUP 270
- APPENDIX H 273
- H.4 REMOTE DATALOGGER 275
- PROGRAMMING 275
- I.1 TERMINOLOGY 277
- I.2 COMMUNICATIONS AND 277
- COMPATIBILITY 277
- I.3 MORE ON MODBUS 278
- AND CR23X MANUALS 283
- AD1 Major Differences 285
- AD3.1 Programming changes 286
- Section 12 289
- TABLE DATA ADDENDUM 290
- OV4. PROGRAMMING THE CR10X 291
- 03:P84 Data Table Instruction 296
- OV6. DATA RETRIEVAL OPTIONS 297
- DATALOGGER 298
- COMPUTER 298
- SECTION 1. FUNCTIONAL MODES 299
- STATUS - ∗B 301
- 1.7 ∗C MODE -- SECURITY 301
- 1.8 ∗D MODE – TRANSFER 301
- PROGRAMS, GENERAL SETTINGS 301
- 1.9 *9 DATA TABLES SIZES 305
- 2.1 FINAL STORAGE AND DATA 307
- LOOP TO RUN AM416 MULTIPLEXER 315
- TO COUNT SWITCH CLOSURES 317
- (RAIN GAGE) 317
- 8.5 SDM-A04 ANALOG OUTPUT 318
- Section 12. Program Control 327
- Instructions 327
- Security 332
- Remote Location/Coil/Register 332
- Remote Location 333
- Local Location 333
- Send Message (P192) 334
- Message Type 335
- Number of Remotes 336
- First Remote Address 336
- Time into Transmit Interval 336
- Transmit Interval 336
- Swath to Receive 337
- Seconds Until Transmit (P194) 338
- Swath to Receive From Master 340
- Swath to Send 340
- First Location to Send 340
- Force Route (P197) 341
- Set Setting (P198) 341
- Result Location 342
- Beacon Intervals 343
- Neighbor Filter 344
- LIST OF TABLES 345
- LIST OF FIGURES 349
- 9. INPUT/OUTPUT INSTRUCTIONS 350
- 10. PROCESSING INSTRUCTIONS 350
- 13. CR10X MEASUREMENTS 350
- CR10X INDEX 353
Produits connexes et manuels pour Instruments de mesure Campbell-scientific CR10X Measurement and Control System
Instruments de mesure Campbell-scientific CR5000 Measurement and Control Module Manuel d'utilisateur
(238 pages)
(238 pages)
Instruments de mesure Campbell-scientific CR1000 Measurement and Control System Manuel d'utilisateur
(588 pages)
(588 pages)
Instruments de mesure Campbell-scientific CR7 Measurement and Control System Manuel d'utilisateur
(186 pages)
(186 pages)
Instruments de mesure Campbell-scientific CS11-L Current Transformer Manuel d'utilisateur
(36 pages)
(36 pages)
Instruments de mesure Campbell-scientific CS110 Electric Field Meter Manuel d'utilisateur
(88 pages)
(88 pages)
Instruments de mesure Campbell-scientific CS205 10-Hour Fuel Temperature Stick Manuel d'utilisateur
(10 pages)
(10 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.151 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels