Campbell-scientific PONDVIEW Real-Time Monitoring & Control Softwa Manuel d'utilisateur

PONDVIEW 4.0CSI AQUACULTUREAUTOMATED MONITORING AND CONTROL SUPPORT SOFTWAREINSTRUCTION MANUALREVISION: 6/02COPYRIGHT (c) 2000-2002 CAMPBELL SCIENTIF

PondView Introduction4This is a blank page.

1-1Section 1. Setting Up the Network andCommunicating1.1 Getting StartedWith the software installed, you are probably anxious to start using PondVie

Section 1. Setting Up the Network and Communicating1-21.2.2 Configure CommunicationThe Setup Screen is used to configure your CR10X-TD network, defi

Section 1. Setting Up the Network and Communicating1-3then the PakBusPort, then the CR10X-PB, this is the path of communicationfrom the PC to the CR1

Section 1. Setting Up the Network and Communicating1-4Once all devices are added to the device map, complete the forms associatedwith each device. R

Section 1. Setting Up the Network and Communicating1-51.3.3.1 Hardware TabCommunication Enable - Before communications can take place, all devices i

Section 1. Setting Up the Network and Communicating1-61.3.3.3 Scheduled Collection TabThe Scheduled Collection tab defines when PondView will automa

Section 1. Setting Up the Network and Communicating1-71.3.3.4 Clock Check/Set TabAutomated Clock Check - Enable this to compare the CR10X-TD clock t

Section 1. Setting Up the Network and Communicating1-8This is a blank page.

2-1Section 2. PondView Display Screen2.1 Enable the DisplayPondView is activated by selecting Start|Programs|PondView.When PondView is first started

This is a blank page.

Section 2. PondView Display Screen2-22.3 Pond PageThe Pond Page provides a desktop display for real-time dissolved oxygen andmotor amps, and is used

Section 2. PondView Display Screen2-32.4 Temperature ThermometerThe temperature thermometer can be use to monitor temperature in degreesFahrenheit o

Section 2. PondView Display Screen2-4This is a blank page.

3-1Section 3. Control Set Points andAlarms3.1 Control Set Points3.1.1 Aerator ControlThe CR10X-TD automatically controls each aerator. If the diss

Section 3. Control Set Points and Alarms3-23.2 AlarmsPondView provides audio and visual alarms to indicate when critical levelshave been reached. T

Section 3. Control Set Points and Alarms3-33.2.2 Dissolved Oxygen AlarmTo select the slider bars for DO alarm set points, double click on the CLICKF

Section 3. Control Set Points and Alarms3-4This is a blank page.

4-1Section 4. Manual ControlThe automated feature of the CR10X-TD can be overridden using thePondView monitor. Switching aerators on or off can also

Section 4. Manual Control4-2This is a blank page.

5-1Section 5. Timer Aerator ControlIn addition to the aerators being controlled automatically be the condition ofthe dissolved oxygen, and manually b

Limited WarrantyCAMPBELL SCIENTIFIC, INC. warrants that the media on which the accompanyingcomputer software is recorded and the documentation provide

Section 5. Timer Aerator Control5-2This is a blank page.

6-1Section 6. DO Probe Calibration6.1 Dissolved Oxygen CalibrationThe CR10X-TD is programmed to allow for both automatic dissolved oxygenair calibra

Section 6. DO Probe Calibration6-2is to be calibrated. Enter the value obtained using the hand dissolved oxygenmeter. Press the Enter key on the PC

7-1Section 7. Communication StatusCommunication Status (Status Monitor) provides a way to monitorcommunication statistics for the CR10X-TD network.

Section 7. Communication Status7-2This is a blank page.

8-1Section 8. Remote Buoy8.1 Wireless Dissolved Oxygen ProbePondView provides data to view the current conditions of the wirelessdissolved oxygen pr

Section 8. Remote Buoy8-2This is a blank page.

9-1Section 9. TroubleshootingProblem SolutionPondView Screen does not representmy pond lay out.PondView is shipped with astandard .INI file that repr

Section 9. Troubleshooting9-2This is a blank page.

License for UseThis software is protected by both the United States copyright law andinternational copyright treaty provisions. You may copy it onto

iPondView Table of ContentsPondView Introduction...1I.1 Please Read This...

PondView Table of Contentsii7. Communication Status... 7-18. Remote Buoy...

1PondView IntroductionI.1 Please Read ThisWelcome to PondView, Campbell Scientific’s Windows compatible supportsoftware for CR10X-TD Monitoring and C

PondView Introduction2If remote PCs are being used to network with the main server computer, thenPondView is the only installation that is required.

PondView Introduction3The Path should read: “ C:\Program Files\Campbellsci\PondView\PondView.exe” 192.168.22.131 username password 6789The 192.168.2