Campbell-scientific CR800 and CR850 Measurement and Control Systems Manuel d'utilisateur Page 501
- Page / 566
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix A. CRBasic Programming Instructions
501
LoadFieldCal
LoadsvaluesfromtheFieldCalfileintovariablesinthedatalogger.
Syntax
LoadFieldCal(CheckSig)
NewFieldCal
TriggersstorageofFieldCalvalueswhenanewFieldCalfilehasbeenwritten.
Syntax
DataTable(TableName, NewFieldCal, Size)
SampleFieldCal
EndTable
SampleFieldCal
StoresthevaluesintheFieldCalfiletoadatatable.
Syntax
DataTable(TableName, NewFieldCal, Size)
SampleFieldCal
EndTable
A.20 Satellite Systems
Instructions for GOES, ARGOS, INMARSAT-C, OMNISAT. Refer to satellite
transmitter manuals available at www.campbellsci.com.
A.20.1 Argos
ArgosData
SpecifiesthedatatobetransmittedtotheArgossatellite.
Syntax
ArgosData(ResultCode, ST20Buffer, DataTable, NumRecords,
DataFormat)
ArgosDataRepeat
SetstherepeatratefortheArgosDatainstruction.
Syntax
ArgosDataRepeat(ResultCode, RepeatRate, RepeatCount,
BufferArray)
ArgosError
Sendsa"GetandClearErrorMessage"commandtothetransmitter.
Syntax
ArgosError(ResultCode, ErrorCodes)
ArgosSetup
SetsupthedataloggerfortransmittingdataviaanArgossatellite.
Syntax
ArgosSetup(ResultCode, ST20Buffer, DecimalID, HexadecimalID,
Frequency)
- CR800 Measurement and 1
- Control System 1
- Warranty 3
- Assistance 5
- 2).................... 159 10
- List of Figures 18
- List of Tables 21
- ................ 1279H142 24
- Table of Contents 26
- Section 1. Introduction 27
- 4.1.1.1 Sensors 33
- 4.1.1.2 Datalogger 33
- 4.1.1.3 Data Retrieval 33
- 4.1.2.1 Wiring Panel 34
- Figure 2: Wiring panel 35
- 4.1.3 Sensors 36
- 4.1.3.2 Bridge Sensors 37
- 4.1.3.3 Pulse Sensors 38
- (p. 307) ) 39
- 4.1.3.4 RS-232 Sensors 40
- 4.1.4 Digital I/O Ports 42
- 4.1.5 SDM Channels 42
- 4.2.1 What You Will Need 43
- 4.2.2 Hardware Setup 43
- 4.2.3 PC200W Software Setup 44
- Section 5. System Overview 57
- 5.1 CR800 Datalogger 58
- 5.1.1 Clock 59
- 5.1.2 Sensor Support 59
- 5.1.3 CR800 Wiring Panel 60
- 5.1.3.2 Voltage Outputs 61
- 5.1.3.3 Grounding Terminals 62
- 5.1.3.4 Power Terminals 62
- 5.1.3.5 Communications Ports 63
- 5.1.5 Power Requirements 64
- 5.1.6 Programming 65
- (p. 315) 66
- (p. 505) ) 66
- 5.1.8 Data Retrieval 67
- 5.1.9 Communications 68
- 5.1.9.2 Modbus 69
- 5.1.9.3 DNP3 Communication 69
- 5.1.9.4 Keyboard Display 69
- 5.1.10 Security 70
- 5.1.10.1 Vulnerabilities 71
- 5.1.10.2 Pass-code Lockout 72
- 5.1.10.3 Passwords 73
- 5.1.10.4 File Encryption 74
- 5.1.11 Maintenance 75
- 5.1.11.3 Calibration 76
- 5.1.11.4 Internal Battery 76
- formoreinformation. 79
- Section 7. Installation 81
- 7.4 Power Sources 82
- 7.4.3 Power Supplies 83
- (p. 82) 84
- (p. 84) lists the 84
- (p. 312) 84
- to understand 85
- 7.5 Grounding 86
- 7.5.1.1 Lightning Protection 88
- (p. 86), use of a simple 89
- (p. 89) shows a simple 89
- 7.6 CR800 Configuration 92
- (p. 95) ) lists 94
- (p. 95), when the 94
- 7.6.3 Settings 96
- (p. 70) 99
- (p. 100), the 99
- 7.6.3.2 Settings via CRBasic 102
- 7.6.3.3 Durable Settings 103
- (p. 105) 105
- 7.6.3.5 Network Planner 107
- 7.7 Programming 108
- 7.7.1.2 CRBasic Editor 109
- 7.7.2 Sending Programs 110
- -Number of fields per record 111
- 7.7.3 Syntax 112
- 7.7.3.2 Structure 113
- Section 7. Installation 114
- 7.7.3.3 Command Line 115
- (p. 117) shows 117
- (p. 237) 118
- Zero Minimum Maximum 119
- Table 10. Data Types 120
- (p. 121) shows an example 121
- (p. 122) 122
- (p. 188) 122
- (p. 421) ) 122
- NextScan 123
- (p. 202) ) 124
- 7.7.3.5 Declared Sequences 125
- (p. 127). The data file 126
- (p. 126) 126
- (p. 127) 126
- (p. 149) for a list 127
- (p. 127), data 127
- (p. 130) ) 128
- (p. 269) 130
- (p. 127), three 130
- (p. 133) 132
- 2. Background calibration 134
- 4. Processing tasks 134
- 7.7.3.7 Execution Timing 135
- (p. 136): 136
- (p. 136), the scan is 136
- (p. 285) 137
- (p. 442) after complete 138
- (p. 310) 138
- 7.7.3.8 Instructions 139
- (p. 140) 140
- 7.7.3.9 Expressions 142
- TempF = TempC * 1.8 + 32 143
- (p. 147) demonstrate 146
- (p. 148) demonstrates 147
- 7.7.4 Tips 150
- 7.8.1.1 CAL Files 151
- 7.8.1.2 CRBasic Programming 152
- (p. 159) and Two Point 153
- (p. 431) menu commands to 154
- (p. 155) to the 155
- (p. 156) 156
- (p. 158) to the 158
- (p. 160) to the CR800 160
- (p. 161) to 161
- KnownWC = 0 162
- (p. 431) menu to delete 163
- (p. 164) as a program to 163
- (p. 164) sent to the 165
- (p. 165), keep the 249-kΩ 166
- (p. 167) 166
- 7.8.2 Information Services 167
- (p. 545) 168
- (p. 169), this page 168
- (p. 170) 169
- CRBasicExample32. HTML 171
- 7.8.2.4 FTP Server 172
- 7.8.2.5 FTP Client 172
- 7.8.2.6 Telnet 172
- 7.8.2.7 SNMP 172
- 7.8.2.8 Ping 172
- 7.8.3 SDI-12 Sensor Support 173
- (p. 174) 174
- (p. 179) summarizes CR800 179
- (p. 207) 184
- (p. 186) 185
- 7.8.4 Subroutines 188
- 7.8.5 Wind Vector 189
- 7.8.5.1 OutputOpt Parameters 190
- (p. 193) ) that 192
- 7.8.6 Custom Menus 194
- (p. 197) 195
- (p. 195) through Custom 197
- 7.8.8 Serial I/O 201
- 7.8.8.1 Introduction 202
- 7.8.8.2 I/O Ports 203
- 7.8.8.3 Protocols 203
- 7.8.8.4 Glossary of Terms 204
- 7.8.8.5 CRBasic Programming 205
- (p. 207) ). Data may be 209
- 8.1 °C" 210
- #01 84 cr 210
- Dim SerialInString As Long 210
- 7.8.8.6 Testing Applications 212
- (p. 216) imports 216
- (p. 382 216
- 7.8.8.7 Q & A 221
- Processing 223
- 7.8.10 NSEC Data Type 224
- 7.8.10.1 NSEC Options 225
- 7.8.11 Bool8 Data Type 228
- (p. 433) ). The CR800 232
- (p. 426) of 232
- (p. 233), summarizes the 232
- This is 237
- 7.8.13.1 String Operators 238
- 7.8.14 Data Tables 241
- (p. 60) ) 242
- 7.8.16 Program Signatures 243
- (p. 248) demonstrates: 248
- 7.8.17.5 Scaling Array 251
- 7.8.17.6 Conditional Output 252
- 7.8.17.7 Capturing Events 253
- 7.8.18 PRT Measurement 254
- (p. 260) for wiring diagram 260
- 0.025 V > (V 261
- * 115.54)/(9900+115.54) 261
- < 2.16 V 261
- BRFull() are 0.001 and 263
- 7.8.19 Running Average 264
- Section 8. Operation 269
- 8.1.2 Voltage 270
- 8.1.2.1 Input Limits 271
- 8.1.2.2 Reducing Error 272
- 8.1.2.3 Measurement Sequence 273
- Error, 274
- Error 275
- 8.1.2.5 Voltage Range 276
- (p. 276) ) 277
- 8.1.2.7 Integration 279
- (p. 280) and 280
- (p. 281) 281
- 8.1.2.8 Signal Settling Time 282
- (p. 108) 284
- (p. 278) 285
- COUNTS = G * Vin + B 286
- ±mV Input 287
- Section 8. Operation 288
- (p. 539) 291
- 8.1.3.1 ac Excitation 293
- (p. 91) 294
- 8.1.3.3 Strain Calculations 296
- 8.1.4 Thermocouple 297
- 8.1.5 Pulse 297
- (p. 538) for information 301
- (p. 303) 301
- (p. 303) 301
- (p. 304) lists 304
- (p. 306) footnote 306
- 8.1.6 Period Averaging 307
- 8.1.7 SDI-12 Recording 308
- 8.1.8 RS-232 and TTL 308
- 8.1.9 Field Calibration 309
- 8.1.10 Cabling Effects 309
- 8.1.10.3 RS-232 Sensors 310
- 8.1.10.4 SDI-12 Sensors 310
- , www.campbellsci.com, or 311
- 8.2.4 Control Outputs 312
- (p. 314) 313
- 8.2.6 TIMs 315
- 8.2.7 Vibrating Wire 315
- 8.2.8 Low-level ac 315
- 8.3.1 Storage Media 315
- Table 71. CR800 SRAM Memory 317
- 8.3.1.1 Data Storage 318
- (p.448) 321
- format. 322
- 8.3.2 Memory Conservation 323
- 8.3.3 Memory Reset 323
- 8.3.4 File Management 324
- 8.3.4.1 File Attributes 326
- 8.3.4.2 Data Preservation 326
- drive. The steps to copy 327
- (p. 431) feature. The 327
- Command,File,Device 328
- (p. 433) or 329
- 8.3.5 File Names 331
- 8.3.6 File System Errors 331
- 8.4.2 Protocols 333
- 8.5 PakBus Overview 334
- 8.5.1 PakBus Addresses 335
- (p. 335) ): 337
- 8.5.3.4 Neighbor Lists 338
- 8.5.3.5 Adjusting Links 338
- 8.5.3.6 Maintaining Links 338
- 8.5.4 PakBus Troubleshooting 339
- 8.5.4.3 Traffic Flow 340
- 8.5.6 PakBus LAN Example 341
- 8.5.6.2 LAN Setup 342
- 8.5.6.3 LoggerNet Setup 344
- (p. 345), set the 345
- 8.5.7 PakBus Encryption 346
- 8.6.1 DNP3 347
- (p.349), 348
- (p.349),line24. 348
- (p. 349), program the 349
- 8.6.2 Modbus 350
- 8.6.2.2 Terminology 351
- (p. 352) shows the 352
- 8.6.2.4 Troubleshooting 353
- 8.6.2.5 Modbus over IP 354
- 8.6.2.6 Modbus tidBytes 354
- 8.6.3 Web Service API 355
- 8.6.3.2 Command Syntax 356
- (p. 358) 357
- 8.6.3.3 Time Syntax 358
- 8.6.3.4 Data Management 358
- section 359
- (p. 358) section) 363
- (p. 358) for 363
- (p. 358) for format 363
- XML Response 365
- 8.6.3.5 Control 368
- 8.6.3.6 Clock Functions 370
- 8.6.3.7 Files Management 374
- (p. 76) Connect screen 375
- HTML page source: 379
- 8.7 Support Software 382
- 8.8.1 Data Display 385
- 8.8.1.2 Real-Time Custom 386
- Figure 116: Real-time custom 387
- 8.8.1.3 Final-Storage Tables 388
- 8.8.2 Run/Stop Program 389
- 8.8.3 File Display 390
- 8.8.3.1 File: Edit 391
- 8.8.4 Ports and Status 392
- 8.8.5 Settings 392
- 8.8.6 Configure Display 393
- Small program 2,600 1,113 395
- Large program 32,157 7,085 395
- Section 9. Maintenance 397
- Manufacturer Tadiran 398
- Model TL-5902S (3.6 V) 398
- Capacity 1.2 Ah 398
- 9.3 Repair 400
- Section 9. Maintenance 402
- Section 10. Troubleshooting 403
- 10.3.1.1 CompileResults 404
- 10.3.1.2 SkippedScan 405
- 10.3.1.3 SkippedSlowScan 405
- 10.3.1.4 SkippedRecord 405
- 10.3.1.5 ProgErrors 406
- 10.3.1.6 MemoryFree 406
- 10.3.1.7 VarOutOfBounds 406
- 10.3.1.8 WatchdogErrors 406
- 10.3.4 NAN and ±INF 408
- 10.4 Communications 411
- 10.4.3.2 CommsMemFree(2) 413
- 10.4.3.3 CommsMemFree(3) 413
- 10.5 Power Supplies 414
- 10.5.3.1 Battery Test 415
- 12V terminal and a G 417
- OFF and allow 417
- (p. 3) 418
- 419
- Section 10. Troubleshooting 420
- 10.6 Terminal Emulator 421
- (p. 422) 422
- Section 11. Glossary 425
- (p.436) 426
- (p.445). 428
- (p.545). 428
- (p.76)andtheappendix 429
- (p.547). 429
- (p.447). 429
- (p. 76) 431
- (p.518). 434
- (p.167)and 434
- (p. 545) ) to 436
- (p.438). 437
- Battery(BattV) 439
- (p.439). 440
- (p.449). 441
- inCR800measurement 442
- (p.76).A 445
- (p.546).Software 445
- (p.425)). 445
- (p.442). 445
- (p.427). 445
- ,formore 448
- 11.2 Concepts 449
- Section 11. Glossary 450
- Instructions 451
- (p.167). 452
- A.2 Data-Table Declarations 453
- A.2.2 Data Destinations 454
- A.2.3.1 Single-Source 455
- A.2.3.2 Multiple-Source 456
- A.5 Measurement Instructions 461
- A.5.2 Voltage 462
- A.5.3 Thermocouples 462
- BrHalf4W 463
- PulseCount 463
- A.5.7 Digital I/O 464
- SDI12SensorSetup 465
- Therm108 467
- Therm109 467
- SDMTrigger 470
- A.6.2 Arithmetic Operators 471
- A.6.3 Bitwise Operators 471
- (p. 473) 472
- A.6.5 Logical Operators 473
- A.6.6.1 Derived Functions 474
- A.6.6.2 Intrinsic Functions 474
- A.6.7 Arithmetic Functions 475
- A.6.8 Integrated Processing 477
- A.6.9 Spatial Processing 478
- A.6.10 Other Functions 479
- A.7 String Functions 480
- A.7.2 String Commands 481
- A.8 Clock Functions 483
- A.9 Voice-Modem Instructions 485
- NumBytes) 487
- Broadcast(ComPort, Message) 489
- A.13 Variable Management 492
- A.14 File Management 493
- A.16 Information Services 496
- NTPMaxMSec) 498
- A.17 Modem Control 499
- A.18 SCADA 499
- Mode, KnownVar, Index, Avg) 500
- A.20 Satellite Systems 501
- RInterval) 502
- A.21 User Defined Functions 503
- (p. 92) 505
- (p. 413) (see 506
- (p. 413) ) 506
- (p. 413) 513
- Each integration / range 516
- UTC. This offset is used in 518
- Table 118. CR800 Settings 519
- C.2.1 Pin-Out 527
- C.2.2 Power States 528
- Connections* 529
- Appendix E. FP2 Data Format 535
- Products 537
- F.2 Sensor Input Modules 538
- F.3 Cameras 540
- F.4 Control Output Modules 541
- F.5 Dataloggers 541
- F.6 Power Supplies 542
- F.6.2 Batteries 543
- F.6.3 Battery Bases 543
- F.6.4 Regulators 543
- F.7 Enclosures 544
- F.8.1 Keyboard Display 545
- F.8.3 Ethernet Link Devices 545
- F.8.4 Telephone 545
- F.9 Data Storage Devices 546
- F.10.3 Software Tools 548
- Table 157. Software Tools 549
Produits connexes et manuels pour Instruments de mesure Campbell-scientific CR800 and CR850 Measurement and Control Systems
Instruments de mesure Campbell-scientific CR9000X Measurement and Control System Manuel d'utilisateur
(442 pages)
(442 pages)
Instruments de mesure Campbell-scientific CS450/CS455 Pressure Transducer Manuel d'utilisateur
(34 pages)
(34 pages)
Instruments de mesure Campbell-scientific CS451/CS456 Pressure Transducer Manuel d'utilisateur
(48 pages)
(48 pages)
Instruments de mesure Campbell-scientific CS470/CS471 Compact Bubbler System Manuel d'utilisateur
(46 pages)
(46 pages)
Instruments de mesure Campbell-scientific CS510 OxyGuard Dissolved Oxygen Probe Manuel d'utilisateur
(12 pages)
(12 pages)
Instruments de mesure Campbell-scientific CS615 Water Content Reflectometer Manuel d'utilisateur
(18 pages)
(18 pages)
Instruments de mesure Campbell-scientific CS511 Dissolved Oxygen Probe Manuel d'utilisateur
(38 pages)
(38 pages)
Instruments de mesure Campbell-scientific CS705 Tipping Bucket Snowfall Adapter Manuel d'utilisateur
(28 pages)
(28 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels