Campbell-scientific CS511 Dissolved Oxygen Probe Manuel d'utilisateur Page 1

CS511-L DissolvedOxygen ProbeRevision: 1/13 Copyright © 2001-2013Campbell Scientific, Inc.

CS511-L Dissolved Oxygen Probe 3. Pour clean water into the lower body and look for leakage around the membrane. Dispose of the water, and if there

CS511-L Dissolved Oxygen Probe 4.2 Use SCWin to Program Datalogger and Generate Wiring Diagram The simplest method for programming the datalogger to

CS511-L Dissolved Oxygen Probe 3. Select CS511 Dissolved Oxygen Probe, and select the right arrow (in center of screen) to add it to the list of sens

CS511-L Dissolved Oxygen Probe 5. Choose the outputs and then select Finish. 6. In the Save As window, enter an appropriate file name and select S

CS511-L Dissolved Oxygen Probe 4.3 Mount Probe Mount the CS511 in water at a slight angle, which prevents bubbles from becoming trapped on the membr

CS511-L Dissolved Oxygen Probe membrane in a screw-on membrane cap. Regular servicing is not required. When necessary, the probe can be fully overha

CS511-L Dissolved Oxygen Probe Shipping Weight 0.8 kg (1.75 lb) Cable Jacket Material: PVC Operating Conditions: Temperature Pressure: Minimum Sub

CS511-L Dissolved Oxygen Probe 7. Operation 7.1 Wiring The CS511 can use one differential channel or one single-ended channel. Differential wiring

CS511-L Dissolved Oxygen Probe 7.2.1.1 Example CR1000 Program Using VoltDiff This example is a CR1000 program but programming for the CR800, CR850, C

CS511-L Dissolved Oxygen Probe 7.2.1.2 Example CR200(X) Program The CR200(X)-series must use the VoltSE() instruction since these dataloggers do not

CS511-L Dissolved Oxygen Probe 7.2.2 Edlog In Edlog, P1 is used for single-ended measurements, and P2 is used for differential measurements. Section

CS511-L Dissolved Oxygen Probe 4) Place the CS511 in air away from direct sunlight with the membrane facing upward. 5) Place a drop of clean water o

CS511-L Dissolved Oxygen Probe 8. Maintenance The only maintenance required is regular cleaning and replacement of the membrane (see below). 8.1 Cle

CS511-L Dissolved Oxygen Probe 3. Using the membrane tool, unscrew the membrane lock that is in the lower body (see FIGURE 8-2). 4. Remove and dispo

CS511-L Dissolved Oxygen Probe 5. To clean, immerse the top part of the sensor in distilled white vinegar (3% acetic acid) for about 30 min. If vine

CS511-L Dissolved Oxygen Probe 6. Replace the membrane and its O-ring by first placing the new O-ring at the very bottom of the membrane cavity (see

CS511-L Dissolved Oxygen Probe FIGURE 8-5. Installing membrane 7. Inspect the membrane for wrinkles; replace membrane if wrinkled. Membrane Lock S

CS511-L Dissolved Oxygen Probe 8. Pour some clean water into the lower body and look for leakage around the membrane (see FIGURE 8-6); replace membra

CS511-L Dissolved Oxygen Probe 22

Appendix A. Dissolved Oxygen Tables A-1

Warranty “PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in materi

Appendix A. Dissolved Oxygen Tables A-2

Appendix B. Sensorex’s Model DO6200/T Prior to June 2008, Campbell Scientific’s CS511 was Sensorex’s model DO6200/T (see FIGURE B-1) instead of Sens

Appendix B. Sensorex’s Model DO6200/T B-2 Dimensions and Weight: 8.9 cm (3.5 in) height, 5.6 cm (2.2 in) diameter, 0.5 kg (1.1 lb) Cable Length: 3 m

Appendix C. PT4-L Agitator C.1 Description The PT4 agitator is a reliable, robust agitator for use in conjunction with probes subjected to bio-foul

Appendix C. PT4-L Agitator FIGURE C-2. DO sensor with PT4 Agitator C.2 PT4-L Specifications Diameter: 8.3 cm (3.25 in) Length: 18.0 cm (7.125

Appendix C. PT4-L Agitator The wiring for the agitator as controlled by this example program is as follows: BLUE WHITE Agitator +

Appendix C. PT4-L Agitator C-4 The CR510, CR10X, and CR23X use instruction P86 and P22 as follows: CR10X P86 and P22 Instructions Example 45: Do (P8

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbel

Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing

Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to spec

Table of Contents ii B. Sensorex’s Model DO6200/T ...B-1 B.1 DO6200/T Specifications ...

CS511-L Dissolved Oxygen Probe 1. Introduction The CS511 is a rugged, low-maintenance sensor that is manufactured by Sensorex. It consists of a sel

CS511-L Dissolved Oxygen Probe 2. Cautionary Statements • The CS511 is a precision instrument. Please handle it with care. • Because the CS511 is

CS511-L Dissolved Oxygen Probe 4. Quickstart Please review Section 7, Operation, for wiring, programming, and calibration information. 4.1 Getting